Victron - Argofet Battery Isolator 200-3
Review: 5 - "A masterpiece of literature" by , written on May 4, 2006
I really enjoyed this book. It captures the essential challenge people face as they try make sense of their lives and grow to adulthood.

Victron - Argofet Battery Isolator 200-3

Available: In Stock
55.000 KD
Image
Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. 

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.

When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.

 Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!

 Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. 

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.

When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.

 Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!

 Alternator energize input

Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.

يتم توصيل الطلبات المحلية في دولة الكويت خلال يوم إلى يومين عمل و الطلبات الخارجية تستغرق خمسة الى اربعة
.عشر يوم حسب الدولة

.تكلفة توصيل الطلبات المحلية ۲ دينار كويتي لكل المناطق عدا الجزر و المناطق البرية 

 تكلفة الشحن للطلبات الدولية تعتمد على حسب الدولة و وزن و أبعاد المنتجات المطلوبة و سوف يتم التواصل مع  العميل بعد إتمام عملية الطلب لإبلاغه بالتكلفة

يمكن للعميل إسترجاع البضاعة او تبديلها او استرجاع مبلغ البضاعة بالكامل (معدا رسوم التوصيل) خلال 14 يوم
من تاريخ الشراء طالما لم يتم فتح او تخريب المنتج و بشرط ان يكون المنتج بوضعه الجديد و قابل لإعادة البيع

.يتم تاكيد الطلب بعد التاكد من توفر المنتج 
.في حال عدم توفر المنتج او عدم صلاحية بيعه بسبب التلف او غيره يتم استرجاع المبلغ بالكامل

جميع المنتجات مكفولة من الوكيل المحلي و في حال وجود اي خلل او عطل مصنعي يتوجب التوجه للوكيل المحلي مباشرة.

يوافق العميل على جميع الشروط المذكورة عند استلام الفاتورة.


Delivery within the state of Kuwait usually takes 1 to 2 working days and international delivery takes upwards of 5 to 14 days.

Local delivery charges are 2 KWD for all urban areas including chalets & farms.


International delivery charges are linked to the weight & dimensions of the products ordered and will be calculated after the order has been submitted.

Orders will only be confirmed after all the order's product have confirmed their availability.

Due to any error in the availability or the irregular condition of the product, the customer will receive a full refund of the paid amount.

Returns and refunds are possible (Except delivery charges) within 14 days of the purchase date if the product has not been damaged or opened and is in it's original condition.

All products are under local distributor warranty policy, if it has a manufacture defect or failure. Please contact the dealer directly.


The Customer agrees on all the mentioned policies upon receiving the order.