DIGITAL THERMATIC^® FAN SWITCH KIT (Part #0444)

Our very own designed Digital Thermatic Fan Switch Kit can be used with our Thermatic Fans, EWP's and competitors Fans.

The sensor, a Temperature Probe (Air or Coolant Fitment) senses air temperature as it passes through the radiator with the sensor placed in the radiator fin section or the sensor can also be placed directly into the coolant system in combination with a Temperature Sensor Adaptor Kit (Part 0409) which is available from our store.

Sensor Wire length:

• 142cm in total (Wire from switch 112cm plus sensor connector 30cm)
• Post 15-Dec-2021 = 320cm total (Wire from switch 290cm plus sensor connector 30cm)

*The sensor wire has been increased to 320cm from the 15-Dec-2021, batch date 2021

The switch can run 1 or 2 fans and be used for 12 or 24 volt applications. It has an adjustable temperature range of 40ºC to 110ºC (104ºF to 230ºF) which can show Centigrade or Fahrenheit.

• Fan #1 will start once the temperature reaches the set temperature.
• Fan #2 (if applicable) will start operation 10 seconds after fan #1 starts. 

The fan/s will operate until the temperature falls by 5°C below the set temperature.

24 Volt Application

Kit sold in 12-volt configuration, for 24-volt application, you will need to purchase 2 x 24-volt relays.

Simply search for part 10534 in our search bar

IP66 Rated:

• Protected from total dust ingress
• Protected from high pressure water jets from any direction, limited ingress protection
• Not waterproof

Integrated electrical noise filter for improved compatibility and reliability in older vehicles that produce high levels of electrical interference and noise.

24 Volt Application

Kit sold in 12 volt configuration, for 24 volt application, you will need to purchase 2 x 24 volt relays. 

Simply search for part 10534 in our search bar (top right-hand side of website).

AIR TEMPRETURE APPLICATION

It senses air temperature as it passes through the radiator and has an adjustable temperature range of 40ºC to 110ºC (104ºF to 230ºF).
The Temperature Sensor is placed in the radiator fin section as close to the hot coolant inlet as possible, no need to cut hoses or can be placed directly into the coolant system.

WATER / COOLANT APPLICATION
The 0444 sensor can also be placed directly into the coolant system. You will need to use a Temperature Sensor Adaptor Kit (Part 0409) to assist with this type of fitment.

We also offer a Digital Thermatic® Fan Switch with 1/4" NPT Thermal Sensor Kit, part number 0445.

SPECIFICATION

• Max voltage: 12 to 27V (For 24V, relays need to be changed, not supplied in kit)
• Max current: Rated to 30 amps per Fan (Maximum 40amp per Fan) Unit comes with 2 x 30 amp fuses and 2 x 40 amp relays

• Relay setup: Dual relay
• Sensor Wire length: 142cm in total (Wire from switch 112cm plus sensor connector 30cm)
• Speed: Single speed, 10 second delay to start up the second fan
• Applications: Suitable for single and dual fan applications
• Screen Display: LED digital temp display, actual temp + set temp
• Temp Display: Centigrade or Fahrenheit
• Temp settings: 40°c to 110°c  (104°F to 230°F)
• Temp setting: Push Button
• Circuit type: Pre-programmed micro controller
• Output wires: Batt + Batt - IGN, AC Clutch, Fan #1, Fan #2 Thermistor Probe
• Dimensions: 95x65x56 mm

*Note: if using this switch for use with our EWP's, it will not vary the speed of the pump in response to engine temperature but rather turn the pump on and off at your set temperature. For EWP control, we would recommend part number 8002 which can manage both the EWP and your Thermatic Fans.   

Delivery within the state of Kuwait usually takes 1 to 2 working days and international delivery takes upwards of 5 to 14 days.

Local delivery charges are 2 KWD for all urban areas including chalets & farms.

International delivery charges are linked to the weight & dimensions of the products ordered and will be calculated after the order has been submitted.

Orders will only be confirmed after all the order's product have confirmed their availability.

Due to any error in the availability or the irregular condition of the product, the customer will receive a full refund of the paid amount.

Returns and refunds are possible (Except delivery charges) within 14 days of the purchase date if the product has not been damaged or opened and is in it's original condition.

All products delivered to customers are in their original sealed conditions (Except products sold on the B-STOCK collection) 

Customers have to refuse any product delivered by the courier incase the product's are not in their original sealed conditions.  

B-stock items are non refundable since they are not sold as new.

All products are under local distributor warranty policy, if it has a manufacture defect or failure. Please contact the dealer directly.

The Customer agrees on all the mentioned policies upon receiving the order.